Quick Navigation
If you use a Kenmore sewing machine, we are going to make your life much easier. This article will give you authentic information about all the error codes of the Kenmore sewing machine and DIY solutions to get rid of those errors.
Once you are done reading, you will be able to solve so many errors of your Kenmore sewing machine yourself and save a lot of time and money.
Error codes of Kenmore sewing machine 385 model
Letβs start exploring some of the common error codes:
Kenmore sewing machine error code E1
Condition of error:
Error code E1 indicates a problem with the zigzag motor of your sewing machine.
Possible parts:
The E1 error means the problem lies in the zigzag motor, fuse, or circuit board of your sewing machine.
Solution advice:
Kenmore sewing machine displays error code E1 when the needle bar is raised but the machine is unable to start the zigzag motor.
You need to unplug your sewing machine and check the connections on circuit board A and the zigzag motor.
If you find that the fuse on circuit board A has blown, then replace the fuse.
If circuit board A has a burned spot or other signs of damage, then replace circuit board A.
However, if both the circuit board A and the fuse are fine, then you need to replace the zigzag motor.
Contact a qualified technician if you are unable to solve the problem.
Kenmore sewing machine error code E2
Condition of error:
Error code E2 indicates that there is an error in the feed motor of your sewing machine.
Possible parts:
In the case of error code E2, the problem lies in the feed motor, circuit board A, or the fuse.
Solution advice:
Error code E2 occurs when the needle bar of your sewing machine is lowered but the machine is unable to start the feed motor.
Unplug your sewing machine and check the wiring connections of circuit board A and the feed motor.
If you find that the fuse on circuit board A has blown, then replace the fuse.
If circuit board A has a burned spot or other signs of damage, then replace circuit board A.
However, if both the circuit board A and the fuse are fine, then you need to replace the feed motor of your machine.
If you are unable to solve the error, contact an expert technician.
Kenmore sewing machine error code E3
Condition of error:
Error code E3 occurs when the circuit board A of your sewing machine has failed or when there are threads jammed inside your machine.
Possible parts:
In error code E3, the problem is located in circuit board A.
Solution advice:
First, you need to check your sewing machine thoroughly and remove all the threads tangled in various parts of the machine.
After that, unplug your sewing machine and check the wiring connections of circuit board A.
If there are burned spots on circuit board A or any other visible sign of damage, you will have to replace circuit board A.
Kenmore sewing machine error codes E4 and E5
Condition of error:
The error codes E4 and E5 of the Kenmore 385 sewing machine are the same.
These errors occur when the upper shaft sensor of your sewing machine has failed or when there are threads jammed in various parts of your machine.
Possible parts:
Error codes E4 and E5 mean the error is located in the circuit board A or the upper shaft sensor.
Solution advice:
First, check your sewing machine thoroughly and remove the threads jammed in any part of the machine.
Next, check the wiring connections of the circuit board (A) and the upper shaft sensor. If you find any loose wires, reconnect them.
If the upper shaft sensor is defective, replace it. If you see burned spots on circuit board A then replace it as well.
Kenmore sewing machine error code: STOP FOR SAFETY PURPOSES
Condition of error:
If the Kenmore sewing machine is telling you to stop for safety reasons, it means the fuse on circuit board A has blown.
Possible parts:
The problem lies in the fuse and circuit board A.
Solution advice:
Unplug the sewing machine and check the circuit board A. If it has burned spots, replace the circuit board. If it has loose wires, reconnect them.
If the circuit board is fine, replace the blown fuse. However, if the fuse keeps blowing again and again, then you need to get your sewing machine serviced.
Error codes of Kenmore Ergo-3 sewing machine
Letβs check the error codes of this model:
Error code 01 β RAISE THE NEEDLE BAR AND PRESSER FOOT, THEN TURN THE POWER ON AGAIN
Condition of error:
When you see this error message along with error code 01 on the screen, it means the X and/or Y carriage motor of your sewing machine has failed.
Possible parts:
The problem is in the A control board, X carriage motor, or Y carriage motor.
Solution advice:
First, unplug your sewing machine and check the wiring connections of the A control board and the X and Y carriage motors. If you find any loose wires, reconnect them.
If the wires are fine, use a multimeter to check the resistance of the carriage motors. The resistance must be 6 ohms or above. If the resistance is lower than 6 ohms or open circuit, the carriage motor should be replaced.
If both carriage motors are working perfectly fine, then replace control board A to solve the problem.
Error code 02 β RAISE THE NEEDLE BAR AND PRESSER FOOT, THEN TURN THE POWER ON AGAIN
Condition of error:
This error message along with error code 02 means the zigzag motor of your sewing machine has failed.
Possible parts:
The problem is with the control board and the zigzag motor.
Solution advice:
First, unplug your sewing machine and check the wiring connections of the A control board and the zigzag motor. If you find any loose wires, reconnect them.
If the wires are fine, use a multimeter to check the resistance of the zigzag motor. The resistance must be 6 ohms or above. If the resistance is lower than 6 ohms or open circuit, the zigzag motor should be replaced.
If the zigzag motor is working perfectly fine, then replace the control board A to solve the problem.
Error code 04 β RAISE THE NEEDLE BAR AND PRESSER FOOT, THEN TURN THE POWER ON AGAIN
Condition of error:
If you see this error message along with error code 04, it means the feed motor of your sewing machine has failed.
Possible parts:
The error is in the control board A or the feed control motor.
Solution advice:
Unplug your sewing machine and check the wiring connections of the A control board and the feed motor. Reconnect all the loose wires.
If the wires are perfect, use a multimeter to check the resistance of the feed motor. The resistance of the feed motor must be 6 ohms or above. If the resistance is lower than 6 ohms or open circuit, the feed motor should be replaced.
If the feed motor is working normally, then replace control board A to solve the problem.
Error code β COMMUNICATION ERROR
Condition of error:
If you see a communication error message on your Kenmore sewing machine, it means the Y-cable has failed.
Possible parts:
The fault is in the Y cable.
Solution advice:
The Y cable is responsible for carrying the data signal reader/writer 19000 to the A control board.
Unplug the sewing machine.
Reconnect the Y cable to the control board A of your sewing machine. Inspect the Y cable thoroughly and replace it if you detect any damage.