Quick Navigation
Are you a regular user of the Typical Sewing Machine? If yes, this article is going to make your sewing much easier because we are going to share a complete list of typical sewing machine error codes along with their causes and solutions.
After reading this, you will be able to diagnose and resolve any error code of your sewing machine and save valuable time.
Let’s get started.
Error codes of Typical GC6910A sewing machine
Here are the 10 error codes of the Typical GC6910A sewing machine:
Error code E01
Cause of error:
The error code E01 appears when the voltage your sewing machine is receiving is too high.
Measurement:
Inspect the AC power.
Error code E03
Cause of error:
The error code E03 is displayed when the voltage is too high.
Measurement:
You need to check the AC power.
Error code E06
Cause of error:
If the current is overloaded, your typical sewing machine will display error code E06.
Measurement:
Check the load.
Error code E08
Cause of error:
When the load is too heavy, your typical sewing machine will show you error code E08 on the screen.
Measurement:
Check the load of your sewing machine.
Error code E09
Cause of error:
If there is a problem with the motor of your sewing machine, you will see the error code E09 on the screen.
Measurement:
Check the motor wire and make sure that it is not too loose or damaged.
Error code E10
Cause of error:
Error code E10 indicates a problem with the synchronizer of your sewing machine.
Measurement:
Check the synchronizer of your sewing machine.
Use your hand to equably rotate the hand wheel, and display “UP” or “UP 1”.
Error code PEDL
Cause of error:
When the error code PEDL appears on your screen, it means the machine is giving you a pedal warning.
Measurement:
You need to release the pedal to solve this problem and the error code will disappear.
Error code CARE
Cause of error:
The error code CARE means the sewing machine is giving you a safety SW warning.
Measurement:
First, you need to check the safety SW.
Set the O31 value to 1.
Error code KEY1
Cause of error:
The error code KEY1 means the machine is giving Input 1 warning.
Measurement:
Check the input 1.
Error code KEY2
Cause of error:
The error code KEY2 means input 2 warning.
Measurement:
Check input 1 and input 2.
Error codes of Typical GC6880 sewing machine
Here are the 12 error codes of a Typical GC6880 sewing machine and the strategies to fix the errors:
Error code E1
Cause of error:
There are three reasons why this error code appears on your screen:
- If the F1 fuse is blown OR the resistor of your sewing machine is damaged.
- If the power module of your sewing machine is faulty.
- If the current or voltage supply to your sewing machine is abnormal.
Solution:
Check the power board and carefully inspect it thoroughly.
The system of your sewing machine will shut down till the power resets ON.
Error code E2
Cause of error:
There are two reasons why error code E02 appears on the screen:
- When the machine is powered ON and the main voltage is too low.
- When you connect the wrong voltage to your sewing machine (the one which is too low).
Solution:
The machine and motor will be powered OFF. Check the main PC board and the AC power.
Error code E3
Cause of error:
The E3 error occurs when there is a communication problem in the operation box linked to the CPU interface.
Solution:
The machine and motor will be turned OFF. Check the Operation Box.
Error code E5
Cause of error:
When there is an error in the connection of the foot pedal, error code E5 is displayed on the screen.
Solution:
The machine and the motor will be powered OFF.
Kindly check the foot pedal connection and make sure it is not too loose or damaged. See if there is any other problem with the foot pedal or its connection.
Error code E7
Cause of error:
There are 4 reasons why error code E7 occurs:
- If the module output is abnormal.
- If the connection of motor connectors is in bad condition.
- If the fabric material you are sewing is too thick.
- If the sewing machine is locked or there is an object stuck in the motor pulley of your machine.
Solution:
Rotate the handwheel with your hand to see if it is jammed due to a mechanical failure.
If the handwheel rotates normally with the hand, it means there is no mechanical error. Now you need to check if the power cord connector, motor encoder connector, and motor are not too loose or damaged. Fix you if you find anything damaged or too loose.
After that, check if the supplied voltage is abnormal or if the sewing speed is too high. If yes, adjust them accordingly.
If nothing works, replace the control box and inform the manufacturer.
Error code E8
Cause of error:
The E8 error code appears when the manual back-tacking lasts for 15 seconds. The problem occurs when the reverse stitching solenoid pulls too long.
Solution:
Try restarting the sewing machine.
If error code E8 appears again upon restart then check if the manual back tack switch is damaged.
Error code E09 & E011
Cause of error:
The error code E09 and E011 both indicate a positioning signal error.
Solution:
Turn off the sewing machine.
Check if the motor encoder interface has fallen off or if it is too loose.
Try restarting the system and see if the motor encoder interface goes back to normal. If it does not, you will have to inform the manufacturer and replace the motor.
Error code E14
Cause of error:
The E14 error code means encoder signal error.
Solution:
Turn off the sewing machine.
Check if the motor encoder interface has fallen off or if it is too loose.
Try restarting the system and see if the motor encoder interface goes back to normal. If it does not, you will have to inform the manufacturer and replace the motor.
Error code E15
Cause of error:
When the error code E15 appears on the screen, it means there is a power module with abnormal over-current protection.
Solution:
Turn off the sewing machine.
Try restarting the system and see if the problem is fixed. If it has not, you will have to inform the manufacturer and replace the control box.
Error code E17
Cause of error:
When the head protection switch of your sewing machine is in the incorrect position, error code E17 appears on the screen.
Solution:
Turn off the sewing machine.
Check if the nose open ball switch control box is damaged or displaced.
Error code E20
Cause of error:
The E20 error code is displayed when the power motor of your sewing machine fails to start.
Solution:
Turn off the sewing machine.
Check if the motor power connection and the motor encoder interface are loose or fall off.
Restart the system and see if they come back to normal. If still nothing works, you need to inform the manufacturer and replace the control box.
Error codes of Typical GT856D sewing machine
Here are the common error codes you will encounter while using a GT856D sewing machine:
Error code E01
Cause of error:
The error code E01 represents the machine’s head tilt.
Solution:
This error occurs when the machine head tilts, the safety switch connecting line is not connected or it has a poor connection.
Error code E02
Cause of error:
The error code E02 occurs when the arm shaft motor speed is abnormal.
Solution:
The encoder wiring and the power line of the arm shaft motor.
Error code E03
Cause of error:
This error occurs when the encoder signals become abnormal.
Solution:
Check the wiring of the arm shaft motor encoder.
Error code E04
Cause of error:
This error occurs when the arm shaft motor is overloaded.
Solution:
See if the supplied voltage is not too low.
Error code E06
Cause of error:
The E06 error code appears when the main board hardware self-test is not passed.
Solution:
It is happening due to the main board failure. Please contact the vendor.
Error code E07
Cause of error:
The E07 error code appears when the main board software self-test is not passed.
Solution:
It is happening due to the main board failure. Please contact the vendor.
Error code E10
Cause of error:
The error code E10 is displayed due to the servo motor driver’s alarm.
Solution:
You need to check the servo motor driver and its wiring.
Error code E11
Cause of error:
The error code E11 occurs in case of arm shaft motor return home failure.
Solution:
You need to check the servo motor driver and its wiring.
Error code E15
Cause of error:
The error code E15 is displayed when there is an abnormal pedal switch signal.
Solution:
It is happening due to pedal switch failure. Please contact your vendor.
Error code E19
Cause of error:
The error code E19 happens when there is a config memory failure.
Solution:
It is happening due to the main board failure. Please contact your vendor.
Error code E21
Cause of error:
The error code E21 occurs in case of zigzag origin search failure.
Solution:
The error is caused when the wiring of the zigzag origin sensor is not connected or the connection is poor.
Secondly, it may occur due to poor induction or a sensor failure.
Error code E22
Cause of error:
The error code E22 occurs due to a feed origin search failure.
Solution:
The error is caused when the wiring of the feed origin sensor is not connected or the connection is poor.
Secondly, it may occur due to poor induction or a sensor failure.
Error code E23
Cause of error:
The error code E23 is displayed when there is no sewing pattern.
Solution:
Select another sewing pattern to solve the problem.
Error code E24
Cause of error:
The error code E24 occurs if the sewing pattern contains invalid data.
Solution:
You need to modify the sewing pattern to solve this problem.
Error code E45
Cause of error:
When the stitch number of the current active sewing patterns exceeds the maximum stitch limit, it leads to error code E45.
Solution:
You need to decrease the total stitch number of the current pattern to solve this problem.
Error code E55
Cause of error:
The error code E55 appears if the pattern already exists in the U-disk.
Solution:
Overwrite the pattern with the same number to solve this error.
Error code E56
Cause of error:
The error code E56 appears if the pattern already exists in the ROM memory.
Solution:
Overwrite the pattern with the same number to solve this error.
Error code E57
Cause of error:
Error code 57 is caused when there is not enough pattern memory left in your sewing machine.
Solution:
Free up the pattern memory space to get rid of this error.
Error code E58
Cause of error:
The error code 58 occurs in case of reading failure from the U-DISK.
Solution:
Check the connection of the U-DISK.
Error code E59
Cause of error:
The E59 error is caused if the U-DISK file format is incompatible.
Solution:
The problem can be solved by converting the file format of U-DISK.
Error code E61
Cause of error:
The error code E61 means POWER OFF.
Solution:
Check the AC power supply.
Error code E62
Cause of error:
The error code E62 means the voltage is too high.
Solution:
You need to check the AC power supply.
Error code E63
Cause of error:
The error code E63 means the voltage is too low.
Solution:
You need to check the AC power supply.
Important Note:
The error code E01 to E20 is fatal error warnings. You must fix the problem before working with the machine again.
Whereas, the error code E21 to E24 are common errors that can be solved by pressing the half-stitch motion key.
Error codes of Typical TC3020GB sewing machine
Let’s take a look at the error codes of this sewing machine:
Error code E010
Cause of error:
The error code E010 occurs when the stop switch was pressed.
Solution:
Press the RESET button to clear the error.
Error code E011
Cause of error:
The error code E11 occurs because the stop switch was pressed.
Solution:
Press the RESET button to clear the error. Also, press the down arrow key to move the work clamp and continue working.
Error code E015
Cause of error:
The error code E15 occurs when the stop switch was still being pressed.
It also occurs due to a problem in the stop switch connection.
Solution:
Turn off the sewing machine.
Check if the P13 connector on the main PC board is properly connected.
Error code E016
Cause of error:
This error occurs due to a problem with the stop switch connection.
Solution:
Turn off the sewing machine.
Check if the P13 connector on the main PC board is properly connected.
Error code E025
Cause of error:
This error code appears when the start switch was being depressed and the power is turned ON. It can also happen if you depress the start switch without lowering the work clamp.
Solution:
If the error occurred because the power was turned ON while the start switch was depressed then you need to turn off the power and check the start switch.
If the error occurred because you did not lower the work clamp and depressed the start switch button then you need to depress the work clamp switch to lower the work clamp before continuing working.
Error code E035
Cause of error:
The E35 error occurs when the work clamp switch is depressed.
Solution:
Turn off the sewing machine and check the work clamp switch.
Error code E036
Cause of error:
The error code E36 appears for two reasons:
- If the work clamp mode is set incorrectly.
- If there is a foot switch that is not properly connected or does not match the specifications.
Solution:
Initialize the memory switch settings OR use a foot switch that matches the specifications.
Error code E050
Cause of error:
When the machine is powered ON and machine head tilting is detected.
Solution:
Turn off the sewing machine.
Restore the machine head to its original position. Check if the P9 connector on the main PC board is properly connected.
Error code E051
Cause of error:
When the sewing machine is operating and the machine head tilting is detected.
Solution:
Turn off the sewing machine.
Check if the P9 connector on the main PC board is properly connected.
Error code E055
Cause of error:
When the machine is powered ON and machine head tilting is detected.
Solution:
Turn off the sewing machine.
Restore the machine head to its original position. Check if the P9 connector on the main PC board is properly connected.
Error code E065
Cause of error:
When the power was turned ON and an operation panel key was being pressed it leads to error code E065.
This error can also occur if the operation panel key is faulty.
Solution:
Turn off the sewing machine and check the operation panel.
Error code E110
Cause of error:
It means needle up stop position error.
Solution:
Turn the machine pulley to the point where the error code E110 disappears.
Error code E111
Cause of error:
It is displayed when the sewing machine is stopped but the upper shaft did not stop at the needle up stop position.
Solution:
Turn the machine pulley to the point where the error code E111 disappears.
Error code E120
Cause of error:
It occurs when the machine cannot detect the needle drop signals.
Solution:
Turn off the sewing machine and then check the connection of the synchronizer.
Error code E121
Cause of error:
It appears when the thread trimming was not completed.
Solution:
Turn off the sewing machine.
Check if the cutting edges of the movable knife and the fixed knife are worn out or damaged.
Error code E130
Cause of error:
When the synchronizer is faulty or the sewing machine stops due to a problem.
Solution:
Turn off the sewing machine and check if the P4 and P5 connectors on the power supply motor PC board are correctly connected or not.
Error code E131
Cause of error:
Error E131 is caused by a faulty synchronizer.
Solution:
Turn off the sewing machine and check if the P5 connector on the power supply motor PC board is properly connected or not.
Error code E132
Cause of error:
Error 132 occurs when a problem is detected with the operation of your sewing machine motor.
Solution:
Turn off the sewing machine and check if the P4 connector on the power supply motor PC board is properly connected or not.
Error code E133
Cause of error:
When the motor stopping position of your sewing machine is not correct, it causes error 133.
Solution:
Turn off the sewing machine and check if the P5 connector on the power supply motor PC board is properly connected or not.
Error code E150
Cause of error:
Error 150 occurs if the temperature sensor is faulty or your sewing machine has overheated.
Solution:
Turn off the sewing machine and then check the motor.
Error code E200
Cause of error:
Error 200 occurs when the home position of the X-feed motor cannot be detected.
It can also happen due to poor connection of the X-home position sensor or a problem in the X-feed motor.
Solution:
Turn off the sewing machine and check if the P10 connector on the PMD PC board and the P20 connector on the main PC board are properly connected.
Error code E201
Cause of error:
When the X-feed motor stops due to a problem, you see error 201 on the screen.
Solution:
Turn off the sewing machine and check if there is something wrong with the X-feed direction.
Error code E202
Cause of error:
It occurs due to a problem in the home position adjustment data of the X-feed and Y-feed motor.
Solution:
Readjusting the home position will solve the problem.
Error code E204
Cause of error:
When the X-feed motor abnormally stops while sewing, it leads to error 204.
Solution:
Turn off the sewing machine and check if there is a problem in the X feed direction.
Error code E205
Cause of error:
When the X feed motor abnormally stops while moving to the sewing start position, it leads to error 205.
Solution:
Turn off the sewing machine and check if there is a problem in the X feed direction.
Error code E206
Cause of error:
When the X-feed motor abnormally stops during test feeding, it leads to error 206.
Solution:
Turn off the sewing machine and check if there is a problem in the X feed direction.
Error code E207
Cause of error:
When the X feed motor abnormally stops during programming, it leads to error 207.
Solution:
Turn off the sewing machine and check if there is a problem in the X feed direction.
Error code E210
Cause of error:
When the home position of the Y-feed cannot be detected, it leads to the error code E210.
It can also happen due to a poor connection of the Y home position sensor or a problem in the Y-feed motor.
Solution:
Turn off the sewing machine and check if the P8 connector on the PMD PC board and the P4 connector on the main PC board are properly connected or not.
Error code E211
Cause of error:
When the Y-feed motor stops due to a problem, you see error 211 on the screen.
Solution:
Turn off the sewing machine and check if there is something wrong with the Y-feed direction.
Error code E214
Cause of error:
When the Y feed motor abnormally stops while sewing, it leads to error 214.
Solution:
Turn off the sewing machine and check if there is something wrong with the Y-feed direction.
Error code E215
Cause of error:
When the Y feed motor abnormally stops while moving to the sewing start position, it leads to error 215.
Solution:
Turn off the sewing machine and check if there is something wrong with the Y-feed direction.
Error code E216
Cause of error:
When the Y feed motor abnormally stops during test feeding, it leads to error 216.
Solution:
Turn off the sewing machine and check if there is something wrong with the Y-feed direction.
Error code E217
Cause of error:
When the Y feed motor abnormally stops during programming, it leads to error 217.
Solution:
Turn off the sewing machine and check if there is something wrong with the Y-feed direction.
Error code E300
Cause of error:
It occurs when the home position of the work clamp cannot be detected.
The error can also be caused due to a problem in the work clamp motor or poor connection of the home position sensor.
Solution:
Turn off the sewing machine and check if the P3 connector on the PMD PC board and the P5 connector on the main PC board are properly connected or not.
Error code E301
Cause of error:
When the raised or lowered position of the intermittent presser footer cannot be detected, it leads to error code 301.
Solution:
Turn off the sewing machine and check if there is a problem in the intermittent foot vertical direction.
Error code E303
Cause of error:
Error 303 is displayed because of a problem in the work clamp motor home position adjustment data.
Solution:
Readjust the home position to solve the problem.
Error code E401
Cause of error:
Error E401 occurs when the sewing machine detects a connection communication error with the PC board power supply motor while the power was turned ON.
Solution:
Turn off the sewing machine and check if the P6 connector on the power supply motor PC board and the P17 connector on the main PC board are properly connected or not.
Error code E402
Cause of error:
This error occurs when your sewing machine detects a communication with the programmer while the power was turned ON.
Solution:
Turn off the sewing machine and check if the P7 connector on the main PC board is properly connected or not.
Error code E403
Cause of error:
Error E403 is displayed when your sewing machine detects a communication error with the PMD PC board while the power was turned ON.
Solution:
Turn off the sewing machine and check if the P1 connector on the PMD PC board is properly connected or not.
Error code E410
Cause of error:
Error E410 is displayed when your sewing machine detects a communication error with the main PC board.
Solution:
Restart the sewing machine.
Error code E411
Cause of error:
Error E411 is displayed when your sewing machine detects a communication error with the power supply motor PC board.
Solution:
Restart the sewing machine.
Error code E412
Cause of error:
Error E412 is displayed when your sewing machine detects a communication error with the programmer.
Solution:
Restart the sewing machine.
Error code E413
Cause of error:
Error E413 is displayed when your sewing machine detects a communication error with the PMD PC board.
Solution:
Restart the sewing machine.
Error code E420
Cause of error:
Error code 420 occurs when there is no CF card inserted.
Error code E421
Cause of error:
Error code 421 occurs when the contents of a program are incorrect, cannot be used, or have no data.
Solution:
Check the floppy disk or CF card which contains data with this program number.
Error code E422
Cause of error:
Error 422 appears when an error occurs while reading the floppy disk or the CF card.
Solution:
Check the data on the floppy disk or the CF card.
Error code E424
Cause of error:
Error 424 is caused when the space on your CF card is insufficient.
Solution:
Use a different CF card with enough space.
Error code E425
Cause of error:
Error 425 is displayed due to an error while writing to the floppy disk or CF card.
Solution:
Always use the specified CF card.
Check if the floppy disk has enough free space.
Check if the floppy disk is write-protected.
Error code E426
Cause of error:
This error occurs when the R/W key has not been pressed.
Solution:
Load the data by pressing the R/W key.
Error code E427
Cause of error:
Error code 427 occurs when the floppy disk or CF card does not have any data with this program number.
Solution:
Check the program number and ensure that it is correct.
If you have already loaded data in the internal memory, it can be used without the need of pressing the R/W key again.
Error code E430
Cause of error:
It happens when it is not possible to back up the data to the main PC board.
Solution:
Restart the sewing machine.
Error code E440
Cause of error:
It occurs due to a data memory error on the main PC board.
Solution:
Restart the sewing machine.
Error code E450
Cause of error:
When it is not possible to read the model selection from the machine head memory, it leads to error code 450.
Solution:
Restart the sewing machine.
Error code E451
Cause of error:
When the data cannot be backed up to the machine head memory, this error occurs.
Solution:
Restart the sewing machine.
Error code E452
Cause of error:
When the machine head memory is not connected, it leads to error code 452.
Solution:
Turn off the sewing machine and check if the P3 connector on the power supply PC board is properly connected or not.
Error code E474
Cause of error:
If the internal memory is full and it is not possible to copy the data, you get error code E474.
Solution:
Clear the sewing data to fix this problem.
Error code E500
Cause of error:
The E500 error occurs when the sewing data extends outside the sewing area due to the enlargement ratio settings.
Solution:
The problem can be fixed by setting the enlargement ratio again.
Error code E501
Cause of error:
When the sewing data extends outside the sewing area was loaded, it leads to this error.
Solution:
Check the sewing data size.
Error code E502
Cause of error:
When the data pitch exceeds 12.7mm because of the enlargement ratio, it leads to error code 502.
Solution:
Set the enlargement ratio again.
Error code E510
Cause of error:
Error 510 occurs due to an invalid code in the sewing data.
Solution:
Reload the data from the floppy disk or the CF card.
Error code E511
Cause of error:
If no end code is input into sewing data, error 511 occurs.
Solution:
Change the program number or input an end code to solve the problem.
Error code E512
Cause of error:
If the number of stitches exceeds the maximum allowed value, error 512 occurs.
Error code E520
Cause of error:
When the extended option output number already exists, you see error code E520 on the screen.
Solution:
First, try changing the extended option output number.
However, if you are not using an extended output option, then you should initialize the data to clear the extended option output data.
Error code E530
Cause of error:
Error code 530 means that changing the program number is not allowed.
Error code E700
Cause of error:
The error code E700 occurs when there is an abnormal rise in the power supply voltage.
Solution:
Disconnect the power and check the input voltage.
Error code E701
Cause of error:
The error code E701 occurs when there is an abnormal rise in the sewing machine motor drive voltage.
Solution:
Disconnect the power and check the input voltage.
Error code E705
Cause of error:
The error code E705 occurs when there is an abnormal drop in the power supply voltage.
Solution:
Disconnect the power and check the input voltage.
Error code E710
Cause of error:
The error code E710 occurs when an abnormal current is detected in the sewing machine motor.
Solution:
Turn off your sewing machine and see if there is something wrong with the machine.
Error code E711
Cause of error:
The E711 error is displayed when the sewing machine detects an abnormal current in the X-FEED motor.
Solution:
Turn off the sewing machine and see if there is something wrong with the X-feed direction.
Error code E712
Cause of error:
The E712 error is displayed when the sewing machine detects an abnormal current in the Y-FEED motor.
Solution:
Turn off the sewing machine and see if there is something wrong with the Y-feed direction.
Error code E713
Cause of error:
The E713 error is displayed when the sewing machine detects an abnormal current in the work clamp motor.
Solution:
Turn off the sewing machine and see if there is something wrong with the work clamp filter, X-feed mechanism, and Y-feed direction.
Error code E730
Cause of error:
The error code E730 occurs when the sewing machine detects external error input (AIRSW).
Solution:
Turn off the sewing machine and check the air pressure.
Error code E740
Cause of error:
When the control box cooling fan stops working, your sewing machine displays the error code E740.
Solution:
Turn off the sewing machine.
Check if the cooling fan is jammed due to tangled threads.
Check if the P22 connector on the main PC board is connected properly.
Error code E741
Cause of error:
When the X-feed motor cooling fan stops working, you get error code 741 on the screen.
Solution:
Turn off the sewing machine.
Check if the cooling fan is jammed due to tangled threads.
Check if the P10 connector on the main PC board is connected properly.
Error code E742
Cause of error:
The error code E742 is displayed when the motor cooling fan of the Y-feed motor stops working.
Solution:
Turn off the sewing machine.
Check if the cooling fan is jammed due to tangled threads.
Check if the P10 connector on the main PC board is connected properly.
